3SGTE Celica MR2 9092 MegaSquirtPNP Gen2 Plug and Play

3SGTE Celica MR2 MegaSquirtPNP Gen2 Plug and Play Standalone Engine Management System is compatible with the following USDM cars with 3S-GTE engines:

1990-1991 Toyota Celica All-Trac (GT-Four) with manual transmission
1991-1992 Toyota MR2 Turbo with manual transmission

These are for USDM pinouts; the pinouts weve found for the 1990-1992 JDM MR2 Turbo look identical. We have not tested this MSPNP on a JDM car, but from all indications it should work. Some markets used different ways to number the model years. See the ECU part number listing at the end of this entry to check if a Toyota ECU not sold in the United States or Canada is compatible.

3SGTE Celica MR2 MegaSquirtPNP Gen2 Plug and Play is easy to Use and Install!

3SGTE Celica MR2 MegaSquirtPNP Gen2 Plug and Play #TS9092 Features:

• • Fully Plug and Play Installation No wiring required for basic functionality, other than wiring theincluded IAT sensor. Install time is about an hour, only exception is if you need to have someone weld in your IAT sensors bung for you real quick. Thatll cost you just a few bucks at most tuner or welding shops.
  • 3S-GTE base maps is pre-loaded to help your engine start on the first turn of the key (other model base maps included on USB thumb drive)
  • Real time tuning and data logging with a laptop connection
  • Supports most aftermarket wideband sensors
• Fully Tunable Engine Control!
  • 1616 Fuel Tables allow high resolution tuning
  • 1212 Ignition Tables
  • Multiple Acceleration enrichment strategies
  • Closed Loop Idle Speed Control
  • Air Conditioner Control
  • 4 sequential fuel injector channels with individual trim tables
  • Onboard peak and hold drivers support both high and low impedance injectors No external ballast resistor is needed!
  • Allows removal of stock mass air flow sensor
• Advanced Feature Set (Included!)
  • 1212 Air Fuel Ratio Target Tables for use with wide band O2 sensor for precise tuning and table trim.
  • Built-in 2-step rev limiter / launch control with flat shift
  • Real time barometric correction
  • Internal 4-bar MAP sensor reads up to 44PSI of boost
  • Overboost protection
  • Closed loop boost control (RequiresEBC solenoid kit, as the stock boost solenoid only works in an on/off fashion)
  • Knock sensor input with adjustable sensitivity
  • Headphone output for knock sensor listen for knock while you tune!
  • Table switching input. Change fuel and spark maps on the fly for different fuels, nitrous activation, etc.
  • Input for flex fuel sensor switch betweenE85and gasoline on the fly!
  • CANBus connector allows interconnection of other MegaSquirt-compatible devices for additional functions (EGT Input, Automatic Transmission Controller, Additional Sensors..the possibilities are limitless!
• What you get in the box:
  • 3SGTE Celica MR2 MegaSquirtPNP Gen2ECU for 90-92
  • MSPNP RS232 serial tuning cable, 6 (USB adapter sold separately, if needed)
  • Tuning Software and DocumentationUSB Stick
  • 6 Vacuum Hose for MAP Signal and T fitting
  • Open element IAT sensor with aluminum mounting bung
  • Four Screws for ECU mounting

Here is a list of Toyota ECU part numbers that this ECU is known to replace.(contact us if you think your ECU should be on this list but isnt!)

• 89661-17320
• 89661-17321
• 89661-17322
• 89661-17330
• 89661-17331
• 89661-17332
• 89661-20750
• 89661-20751
• 89661-20760
• 89661-20761

Note: Although there is a paid upgrade to TunerStudio, it is not needed to tune this ECU. The free version included on the USB Stick can access all the features and tables of the MegaSquirtPNP. The paid version of TunerStudio simply adds tuning and analysis software, such as VE Analyzer Live to tune the fuel tables based on wideband O2 feedback (requiring a wideband O2 sensor and controller, sold separately).